×
Login Form
×
Registration
Profile Informations
Login Datas
or login
Details
Specification:
1, the input power supply (VAC): AC180-260V 50 / 60Hz (for global voltage)
2, the output armature voltage range (VDC): DC220V
3, the output armature current range (A): 8A (0.1A-10A can be arbitrarily set)
If the current is too big need to increase the heat
4, the output excitation voltage range (VDC): 100/200 (default full-bridge rectifier, which is 0.9 times the input voltage)
5, the output excitation current range (A): 1A
6, the working frequency: 16 KHz
7, given signal mode (V / mA): default potentiometer, 0-5V, 0-10V, 4-20mA, PWM, touchtone
8, enable control mode (EN): switch
9, soft start (acceleration time adjustment range) (S): 0-10S (default 2 seconds)
10, soft stop (deceleration time adjustment range) (S): 0-10S (default 2 seconds)
11, double loop PI regulation (voltage and current) control is more reliable
12, IR torque compensation range: 0-100% (default 0)
13, overcurrent range: 0 setpoint (default 8A)
14, overcurrent mode: stop output and indication (display code E1)
15, short-circuit protection: stop output and indication (display code E0)
16, overheat protection: power tube temperature exceeds 100 ° off the output and the indication (display code E2)
17, built-in digital display module can display real-time operating voltage with current
18. Dimensions: Length 140mm × 98mm × height 38mm width
19, Connection: terminal type (convenient)
Advantage
1, using pulse technology to speed more stable, low speed forceful
2, with a short circuit, overcurrent, overtemperature protection cutoff device to make more reliable performance
3, with the elimination of soft starter motor starting current is too large
4, high and low voltage signal is completely isolated, the use of safer
Precaution:
1, the governor closed the input power,
Touched by hand within a minute ban high-voltage terminal,
There are high-voltage capacitors,
To prevent electric shock!!!
2, for the two lines of DC permanent magnet motor,
Two lead wires connected directly to the armature M + with M-.
Prohibit access exciting!
Manual:
PWM signal requirements:
1, the default PWM signal level is 5V, the signal frequency 1KHZ above, with a load capacity of more than 0.5MA.
2,5V level without resistors in series with PWM input port,
10V PWM level from 0-10V input port or serial port 10K resistor in the PWM input,
12V level 3.9K resistor string from 0-10V input port or serial port 13.7K PWM input resistors,
24V level string 27K resistor from 0-10V input port or serial port 16.8K resistor PWM input
Package:
1X AC180V-260V Input DC220V Output 8A PWM DC Motor Speed Controller Driver Digital
1, the input power supply (VAC): AC180-260V 50 / 60Hz (for global voltage)
2, the output armature voltage range (VDC): DC220V
3, the output armature current range (A): 8A (0.1A-10A can be arbitrarily set)
If the current is too big need to increase the heat
4, the output excitation voltage range (VDC): 100/200 (default full-bridge rectifier, which is 0.9 times the input voltage)
5, the output excitation current range (A): 1A
6, the working frequency: 16 KHz
7, given signal mode (V / mA): default potentiometer, 0-5V, 0-10V, 4-20mA, PWM, touchtone
8, enable control mode (EN): switch
9, soft start (acceleration time adjustment range) (S): 0-10S (default 2 seconds)
10, soft stop (deceleration time adjustment range) (S): 0-10S (default 2 seconds)
11, double loop PI regulation (voltage and current) control is more reliable
12, IR torque compensation range: 0-100% (default 0)
13, overcurrent range: 0 setpoint (default 8A)
14, overcurrent mode: stop output and indication (display code E1)
15, short-circuit protection: stop output and indication (display code E0)
16, overheat protection: power tube temperature exceeds 100 ° off the output and the indication (display code E2)
17, built-in digital display module can display real-time operating voltage with current
18. Dimensions: Length 140mm × 98mm × height 38mm width
19, Connection: terminal type (convenient)
Advantage
1, using pulse technology to speed more stable, low speed forceful
2, with a short circuit, overcurrent, overtemperature protection cutoff device to make more reliable performance
3, with the elimination of soft starter motor starting current is too large
4, high and low voltage signal is completely isolated, the use of safer
Precaution:
1, the governor closed the input power,
Touched by hand within a minute ban high-voltage terminal,
There are high-voltage capacitors,
To prevent electric shock!!!
2, for the two lines of DC permanent magnet motor,
Two lead wires connected directly to the armature M + with M-.
Prohibit access exciting!
Manual:
PWM signal requirements:
1, the default PWM signal level is 5V, the signal frequency 1KHZ above, with a load capacity of more than 0.5MA.
2,5V level without resistors in series with PWM input port,
10V PWM level from 0-10V input port or serial port 10K resistor in the PWM input,
12V level 3.9K resistor string from 0-10V input port or serial port 13.7K PWM input resistors,
24V level string 27K resistor from 0-10V input port or serial port 16.8K resistor PWM input
Package:
1X AC180V-260V Input DC220V Output 8A PWM DC Motor Speed Controller Driver Digital
